Back to: 3-piece Ball Valves

DG1 with Orbital weld ends

Print
Description

For use in systems with ultra-clean media
Option: Surface quality of the inner passage Ra 0.8/1.0

DN 8 – DN 100 : Full bore

 

Approvals

               

  • TA-Luft-stem sealing based on the new VDI 2240 directive. Temperature range: tested up to 270 °C (temperature of the medium).
  • Firesafe approval
    accoring to BS 6755, part 2
  • Meets the requirements of the pressure equipment directive PED 97/23/EC
  • Material certificate EN 10204
  • Production monitored by TÜV WO/TRD 100
  • GOST-R Certificate for the Russian Federation

Product features

On the numbered markings you receive further information.      

 

1. Safe connection

Safe connection of all actuators to valve due to direct mounting, Interface acc. DIN 3337 No interruption of stem to acctuator

2. Reliable stem sealing

due to V-rings made of PTFE and equipped with spring washer

3. High switching frequency

due to special primary seal desgin

4. Exact mounting

by means of body screws the centre section is strongly connected with the flanges and is always in correct alignment to the flanges

5. Stem in anti-blowout design

the ball surface is super-polished and absolute round

6. Safe sealing to the outside

due to the separate and fully encapsulated body seal

7. High degree of tightness in bore

due to the special form of the seats. The prestress of the seats causes a spring effect, which results in a reliable sealing function in all pressure ranges. Materials: PTFE/Glass, PTFE/Carbon, PEEK, UHMWPE, POM

8. End connectors:

  • Butt weld end, short
  • Butt weld end, long
  • Orbital butt weld ends
  • Screwed end / female thread / NPT
  • Full bore / reduced bore

Torque chart

kvs
Breakaway torque N**
DIN 3337
Key
DN NPS full
bore
full
bore
Flange Stem  S Ø Stem M1 sw
8
¼"
5
5,5
F03/04
9/11
8
5,5
10
3/8"
9
5,5
F03/04
9/11
8
5,5
15
½"
16
9
F03/04
9/11
9
7
20
¾"
27
12
F03/04
9/11
9
7
25
1"
45
14
F04/05
11/14
9
7
32
1¼"
76
18
F04/05
11/14
11
8
40
1½"
110
20
F04/05
11/14
11
8
50
2"
208
35
F05/07
14/17
14
10
65
360
75
F07/10
17/22
   
80
3"
550
90
F07/10
17/22
   
100
4"
900
135
F07/10
17/22


Breakaway torques refer to ball valves in depressurized condition. They may vary acc. to medium, temperature, pressure and frequency of operation.

** based on water at ambient temperature; seats made of PTFE/Glass

Product advantages

For use in systems with ultra-clean media
Option: Surface quality of the inner passage Ra 0.8/1.0

Safe connection
of all actuators to the valve due to direct mounting interface in compliance with DIN 3337. No interruption of stem to actuator
Reliable stem sealing
V-rings made of PTFE and equpped with spring washer

High switching frequency
due to special primary seal design

Precise assembly
Safety in mounting - by means of body screws the center section is strongly connected with the flanges and is always in correct alignment to the flanges

Anti-blowout stem
inserted from the inside, surface of ball super-polished and precisely formed.

Safe sealing
to the outside by fully encapsulated body seal

High degree of tightness
in the bore due to the special form of the seats. The prestress of the seats results in a reliable sealing function in all pressure ranges

Application range

Applications & Industries

  • Chip industry
  • Chemical industry
  • Process plants
  • Ultra-clean media

Technical data

Nominal sizes:
DN 8 – DN 100 : Full bore

Temperature:

-50°C to +270°C
(Please consider the appropriate pressure/temperature diagram)

Tests:
DIN 3230, T3, BA / BO-1

Materials

 
Body:
Material: Code:
Stainless steel 1.4408  
   
Ball:
Material: Code:
Stainless steel 1.4408  
   
Stem:
Material: Code:
1.4401  
 
Ends:
Material: Code:
AISI 316 L  
   
Seat and body rings:
Material: Code:
PEEK  
POM  
PTFE / glass  
PTFE / carbon  
Virgin PTFE  
UHMWPE  
 
 
 
  • Other materials available!

 

Datenblätter im Downloadbereich